Railway Container Decals

Configure Your Decals

A set of decals for a single container will cost £ 9.50. Any additional sets (of whatever livery) you order at the same time qualify for my multiple decals disount and will cost £ 7.00 each. The discount will be applied in your basket.

To order a set of decals for a container you will need to configure its specification. This will consist of a number of steps, as described below.

To accommodate a wide range of scales, container dimensions are specified in scale feet and/or inches, rather than model mm. A calculator and look-up table to help convert scale inches into model dimensions (or vice versa) is available here (opens in new browser tab/window).

Note: If you want a set of decals for a container that is not covered by the standard options below, I will be happy to quote you for a customised set. Please contact me with full details.


1. Container Livery (and Type)

The first step is to select a livery for your container. With a large number of liveries available, this is done by visiting a separate livery selection page, which shows each livery available, along with information about the prototype. Click on the button there associated with your chosen livery to select it and return to this page. This will also set default values for some of the configuration options below, which you can then change if you wish.

Warning: If you visit the livery selection page after you have started to change any of other settings below (not just the livery settings), you are likely to lose those changes. Either select the livery first, or use this button to save your other settings before visiting the selection page.

No Livery Currently Selected

 

3. Substitute Container Type

The exact container type associated with your chosen livery may not be available as a standard kit or model in your scale. You may therefore wish to use a readily available model of a different type and make it look like the type associated with your chosen livery. To do this you can either select a substitute container type from those that I already have drawings and specification available, or you can specify a custom container type and provide me with the details of your model (see next section). I will then adjust your chosen livery to fit your chosen container type (so if possible please choose a livery for a container type similar in size to your model).

I have a large number of container types available, so selecting a substitute type is also done by visiting a separate container selection page, which shows each type available, along with information about the prototype. Click on the button there associated with your chosen type to select it and return to this page.

Warning: If you visit the container type selection page after you have started to change any of other settings on this page (other than selecting a base livery) you are likely to lose those changes. Either select the substitute type first, or use this button to save your other settings before visiting the selection page.

No substitute container type currently selected

 

4. Custom Container Type

Please use the following controls to specify your custom container type. I will then adjust your chosen livery to fit your chosen container type (so if possible please choose a livery for a container type similar in size to your model). It is possible for you to specify both a subsititute and custom container type. Where there is a conflict in a specification value I will use the following order: custom container value, substitute container value, original container value of the type associated with your chosen base livery. The custom values are therefore all optional, you only need to specify those that differ from either the substitute or original types.

When specifying dimensional values you can use either prototype dimensions or those of your model. Dimensions in mm will be assumed to be of your model. All other units will be assumed to be prototype dimensions and converted to model size using your chosen scale (below). Therefore please specify the units for the values you enter. A handy calculator for converting between prototype and model dimensions is available here (opens in new browser tab/window).

Only needed if shown on container (e.g. BR liveries)

The height of the main lettering area on the sides. For closed containers most of the side lettering was usually concentrated in the upper half of the sides, above a nominal waist level.

For the side and end door type specifications, "One" and "Both" mean doors in one side/end or both sides/ends.

Where a value is shown on the container in both Imperial and metric units (e.g. BR liveries), you only need to specify the Imperial version and I will generate the metric one.

Return the custom values to empty.

 

5. Confirm Configuration

Finally, please specify the scale for your decals, together with a short label (name and/or number) that can be used to distinguish this container decal configuration from any others you may add to your basket:

The uniqueness of this label is important because if you add two different container decal sets with the same label to your basket the more recent specification will overwrite the old. You can, however, use this feature to update the specification of decals you have already added to your basket. The label you enter will be automatically prefixed with "ContainerDecals ".

Once you have selected the appropriate options above to configure this decal set, click on "Confirm Configuration" above to proceed to the next stage of the ordering process. (This will also temporarily store the information you've entered should wish to navigate away to another page, as will the "Save Settings" button above.) You will then be taken to another page showing the information you've entered. From there, you will then be able to either add the set to your basket, or return to this page to change your specification.